Using Pick

Let's take another look at the Pick command on the Sequence menu. (The Section Searching for Messages introduced Pick.) It lets you search for messages by any field in the header, any word(s) in the body, or a combination of these. It's a flexible and powerful way to find messages.

A Pick Example

To select messages, point to one of the boxes by a field name and type what you want to search for. For example, to find messages from nathan, point to the From: box and type nathan.

Figure: Main and Pick windows

In the Figure above, I wanted to find messages which were sent to either the mh-users or mh-workers mailing lists). I pointed to the To: box and typed mh-users. Then, I clicked the Or button next to the window; another box opened, where I typed mh-workers. Because I left the other boxes blank, Pick ignored those fields. If I had filled in one (or more) of them, Pick would have found only messages that fit all the criteria -- for instance, if I had also put the word bug in the Search: box, Pick would have selected only messages to mh-users or mh-workers which contained the word "bug."

Remember that, in some cases, messages may be sent to an address via the To: field or the cc: field. You wouldn't want to type those addresses in the Cc: boxes of the Figure above, though, because the address would have to be listed in both the To: and cc: fields to be matched. In this case, you want the "big -Or-" button.

By default, the Pick window creates a sequence named temp. That sequence is normally reused each time you use Pick. Because I want to keep this sequence for awhile, I changed its name to mailquestions.

Sequence names can be alphabetic characters (letters) only -- if you use an invalid name, xmh won't define the sequence; you'll see a dialog box with an error from the MH pick command.

When I click OK, the Pick window closes. The main window's Table of Contents title changes to project:mailquestions, and the list shows the messages in the sequence. There'll also be an entry on the Sequence menu for the mailquestions sequence. See the Figure below.

Figure: Main window after picking mailquestions sequence

When you're done looking at the sequence, you can select another existing sequence by selecting the name on the Sequence menu, then using Open Sequence. The mailquestions sequence entry will remain, and MH will "remember" the messages in the sequence. Or, you can add and delete messages from a sequence -- see the Section Modifying Sequences.

Using the Big -Or- Button

Figure: Pick window after big -Or- clicked in top area

Find Other Fields, Skip Fields

The box with a blank field name lets you specify another header field besides From:, To:, and so on. For instance, to search for all messages which had the following field:

Reply-To: jerryu

Figure: Example of Pick skip button

Unfortunately, the format of the date you type in the Date: box must match the message exactly. (The Date range: boxes don't have this problem.) As we get closer to the year 2000, more mailers are converting from the old two-digit year format (like 93 for 1993) to using all four digits. So, if you can't use the Date range: boxes, it's safest to type the date with both formats. I did that in the Figure above.

Bottom Area of the Pick Window

• The Creating sequence: box lets you choose the sequence name Pick should write. It defaults to temp. xmh will empty an existing sequence unless you tell it not to. If you want to preserve the messages that are in the sequence and add the new messages to it, be sure you've clicked No next to Clear old entries from sequence?. It's not a good idea to choose a new sequence name each time you use Pick because you can't have more than 26 sequences defined per folder. Sequence names must be alphabetic; uppercase and lowercase letters are distinct, so the sequence named Temp would be different than the one named temp.
• The with msgs from sequence: box tells Pick which message sequence to search for the messages you're picking. This is set automatically to the same sequence that was selected in the main window before you started Pick. Usually, you'll set this to search all messages, but a name besides all can make the search go faster because there'll be fewer messages to search.
• The Date range: boxes take a starting and ending date to search. Pick ignores messages not sent between these two dates. Unfortunately, filling in dates doesn't make the search more efficient, because Pick still has to search all the messages to find what date each one was sent. If the Date field: is empty, Pick gets the date from the Date: field in each message header. That's usually what you want. But you can change it to use, say, Delivery-Date:, if your mail is processed through the MH slocal program.

xmh will put a horizontal scrollbar above this area if it's too wide to fit in the window.

[Table of Contents] [Index] [Previous: Introduction to Sequences] [Next: Modifying Sequences]

This file is from the third edition of the book MH & xmh: Email for Users & Programmers, ISBN 1-56592-093-7, by Jerry Peek. Copyright © 1991, 1992, 1995 by O'Reilly & Associates, Inc. This file is freely-available; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation. For more information, see the file copying.htm.